国产偷国产偷亚-国产无码18p-国产无码av-国产无码不卡-国产无码二区三区-国产无码高清

NABDS Transformer Loss Parameter Tester   NABDS全自動變壓器損耗參數測試儀

產品簡介

NABDS全自動變壓器損耗參數測試儀，采用數字同步采樣技術，準確測量三相用電設備的電壓、電流、功率、功率因數等參數的真有效值，具有測量速度快、精度高、使用方便、輕巧美觀等特點。專門應用于電力變壓器的電量的檢測，該儀表可取代于九塊同等級指針儀表，是傳統電量測試儀表的理想換代產品。

產品別名

變壓器損耗參數測試儀，變壓器損耗參檢測儀

產品特性

1、可測量各種類型的變壓器的空載電流、空載損耗、阻抗電壓、短路損耗。

2、電壓回路寬量限：最大測量電壓750V，不用切換檔位即可保證測量精度。不會因電壓檔位選錯而對儀器本身有所損壞。

3、大屏幕、高亮度的液晶顯示，全漢字菜單及操作提示實現友好的人機對話，操作更簡便。

4、用戶可將測試數據實時打印出來。

5、采用數字同步采樣技術，準確測量三相用電設備的電壓、電流、功率、等參數的真有效值，測量精度為0.2級。

6、NABDS變壓器損耗參數測試儀可取代九塊同等級的指針儀表，是傳統電量測試儀表的理想換代產品。

產品參數

1、輸入特性：電壓測量范圍：0~750V 寬量限。

電流測量范圍：0~100A 內部自動切換量程。

2、準確度： 電壓、電流：±0.2%

功率：±0.2%（COSΦ＞0.1），±0.5% (0.02＜ COSΦ＜0.1)

3、工作溫度：－10℃~ +40℃

4、工作電源：交流160V~265V

5、絕緣：電壓、電流輸入端對機殼的絕緣電阻≥100MΩ。工作電源輸入端對外殼之間承受工頻2KV（有效值），歷時1分鐘實驗。

6、體積：45cm×30cm×21cm

7、重量：3Kg

注意事項

1．在測量過程中一定不要接觸測試線的金屬部分，以避免被電擊傷。

2．測量接線一定要嚴格按說明書操作，否則后果自負。

3．測試之前一定要認真檢查設置的參數是否正確。

4．最好使用有地線的電源插座。

5．不能在電壓和電流過量限的情況下工作。

6．短路試驗時，非加壓側的短接必須良好，否則會對測試結果有影響。

7．做短路試驗時，如果高壓或中壓側出線套管裝有環形電流互感器時，試驗前電流互感器的二次側一定要短接。

8．試驗接線工作必須在被試線路接地的情況下進行，防止感應電壓觸電。所有短路、接地和引線都應有足夠的截面，且必須連接牢靠。測試組織工作要嚴密，通信順暢，以保證測試工作安全順利進行。

NABDS Transformer Loss Parameter Tester

Product introduction

With digital synchronous sampling techniques, accurate measurement of three-phase power equipment voltage, current, power, power factor and other parameters of the true RMS, with high speed, high precision, easy to use, lightweight and beautiful, etc. features. Specifically applied to the detection of power transformer, the meter can be replaced at the same level nine pointer instrument, is the traditional power of the test instrument ideal replacement product.

Also called name

Transformer loss parameter tester, transformer loss parameter detector

The Characteristics of the products

1.A measurable types of transformer load current, load loss, impedance voltage, short circuit losses.

2,Limit the amount of voltage loop width: Maximum measuring voltage 750V, without switching gears to ensure accuracy. Choose the wrong voltage will not stall while the instrument itself is damaged.

3,Large-screen, high brightness LCD display, full English menu and operating tips to achieve a friendly man-machine dialogue, easier to operate.

4,The user can print out the test data in real time.

5,The use of digital synchronous sampling techniques, accurate measurement of three-phase power equipment voltage, current, power, and other parameters of the true RMS measurement accuracy of 0.2.

6,NABDS transformer loss parameter tester can be replaced by a pointer to the same level of nine meters, is the traditional power of the test instrument ideal replacement product.

The parameters of the products

1, The input characteristics: Voltage measuring range: 0 ~ 750V wide quantity is limited.

Current measuring range: 0 ~ 100A internal autoranging.

2, Accuracy: voltage, current: ± 0.2%

Power: ± 0.2% (COSΦ> 0.1), ± 0.5% (0.02 3, Working temperature:-10C ~ +40 ℃

4, Power Supply: AC 160V ~ 265V

5, Insulation: voltage, current input to the chassis insulation resistance ≥ 100MΩ. Work between the power input to the shell to withstand the power frequency 2KV (rms), which lasted one minute experiment.

6, Size: 45cm × 30cm × 21cm

7, Weight: 3Kg

Attention should take 

1. Don’t touch the metal parts during the measurement test to avoid electrically damaging.

2. Wiring must be strictly measured by manual operation.

3. Be sure to carefully check before the test parameters set correctly.

4. Best to use a grounded outlet.

5. Do not limit the voltage and current in case excessive work.

6. Short circuit test, the non-pressurized side must be well short, or would affect the test results.

7. Do short-circuit test, if high or medium voltage side with an annular bushing current transformer, current transformer before testing the secondary side must be shorted.

8. Test wiring work must be grounded in the test line in the case, to prevent induced voltage electric shock. All short circuit, grounding and wire should have sufficient cross-section, and must be firmly connected. Test organization working to tight, smooth communication, in order to ensure the smooth progress of work safety testing.